Rajguru Impex

The Spiral Wound Gaskets are composed of a metallic continuous stripe with a special shaped profile, coupled with a continuous filling stripe (Asbestos, PTFE, Grafoil, Ceramic etc) evenly wound in concentric spiral under constant stress. The Spiral Wound Gaskets are reinforced on the inner and outer diametre by winding of several electrically welded spiral metal only.

Additional Information:

• Production Capacity: As Required
• Delivery Time: Ready

Rajguru Impex is prime manufactureres of Spiral wound gaskets. This type of gaskets, consist of a gasket (winding + filler) with a solid metal outer guide ring. A winding with an alternate combination of a steel strips and soft non-metallic filler with solid outer guide ring. These gaskets can be used on plain flat face flanges and on raised face flanges. The outer guide ring serves to center the gasket properly in the flange joint, acts as an anti-blowout device and compression gauge to prevent spiral wound gasket to prevent the spiral wound component from being crushed. Normally the outer guide rings are furnished in mild steel (carbon steel), but can be supplied in other metal when required by operating conditions.

Additional Information:

• Production Capacity: 10000
• Delivery Time: 1 Day
• Packaging Details: Box packing

Non-Asbestos Fibre materials are so-called because they fill the gap in the range of gasket materials previously occupied by asbestos. Asbestos, although now known to be a dangerous material, had excellent heat resistance properties, which is why it was utilised so widely in high temperature applications. When asbestos was outlawed, replacement materials were needed; and so these asbestos-free, or non-asbestos, materials were developed to perform the same function, but without the corresponding danger to human health.

These materials are now commonly comprised of aramid fibre (Kevlar) and non-organic fibres, which are in turn blended with different polymers to meet different applications: most commonly nitrile rubber, for fuel and oil resistance. These materials can also be graphite coated for non-stick and steam resistance, mixed with PTFE for excellent chemical resistance, or with EPDM for potable water applications.

Additional Information:

• Production Capacity: As Required
• Delivery Time: Ready

Top Supplier & Exporter of Metal Gasket, Spiral Wound Gaskets, Double Jacketed Metal Gaskets Dealer, Solid Metal Gaskets, Flange Gaskets Supplier in Mumbai, IndiaStainless Steel Gaskets, Corrugated Metal Jacketed Gaskets Exporter, Ring Type Joint Gaskets, PTFE Gaskets, Spiral Gaskets Stockholder

Metal gaskets are designed to withstand extreme temperatures, pressures, and chemical exposure applications. It makes easier for various industries to seal the gap between two surfaces to prevent leakage of contents and for other functions. As India’s leading Gaskets Manufacturers, Rajguru Impex offers highest quality Metallic gaskets made in a wide range of materials and grades in accordance with various international standards.

We manufacture & supply a comprehensive range of metal gaskets such as Spiral Wound Gaskets, Double Jacketed Metal Gaskets, Solid Metal Gaskets, Corrugated Metal Jacketed Gaskets, Ring Type Joint Gaskets, PTFE Gaskets, Spiral Gaskets, Flange Gaskets, and many more.

Some of Characterizes of metal gaskets includes:

1. Chemical Resistance
2. Anti-Adhesive Surface
3. Temperature Resistance

Rajguru Impex delivers wide range of gaskets are improvised consistently with the usage of latest technologies. All our gaskets undergo rigorous testing and are certified in accordance with various industry standards as well as environment and safety regulations. 

SS Metal Gaskets, Copper Gaskets, Brass Gaskets, Titanium Gaskets, Monel Gaskets, Hastelloy Gaskets, Inconel Gaskets Trader & Wholesaler in India

Additional Information:

• Packaging Details: Box packing

Rajguru Impex is Manufacturers of ASME B16.20 Ring Joint Gaskets, suitable for high pressure and high temperature applications. The Joint Gaskets are available in R, RX, BX styles and in oval/octagonal profiles. PETROMET FLANGE INC manufacturers in accordance with specific tolerances on CNC machines. OUR Ring Joint Gaskets fully comply with the ASME B16.20 standard and the API spec 6A requirements (where applicable).B16.20 PETROMET FLANGE INC IS HIGHLY ACCLAIMED MANUFACTURER OF RING TYPE JOINTS GASKETS IN TYPE RX , BX , R.Ring Joint Gaskets| R Type RTJ Gaskets| RX Type RTJ Gaskets| BX Type RTJ Gaskets| SBX Type RTJ Gaskets| Speciality RTJ Gaskets| Spiral Wound Gaskets | PTFE Sheets and Gaskets|

Standard Gasket Material

Carbon Steel

Commercial quality sheet steel with an upper temperature limit of approximately 1000º F., particularly if conditions are oxidizing. Not suitable for handling crude acids or aqueous solutions of salts in the neutral or acid range. A high rate of failure may be expected in hot water service if the material is highly stressed, Concentrated acids and most alkalies have little or no action on iron and steel gaskets which are used regularly for such services.

304 Stainless Steel

 An 18-8 (Chromium 18-20%, Nickel 8-10%) Stainless with a maximum recommended working temperature of 1400º F

 

 At least 80% of applications for non-corrosive services can use Type 304 Stainless in the temperature range of -320 F to 1000º F.

 

 Excellent corrosion resistance to a wide variety of chemicals.

 

 Subject to stress corrosion crackling and to intergranular corrosion at temperatures between 800º F to 1500º F in presence of certain media for prolonged periods of time.

316 Stainless Steel

 An18-12 Chromium-Nickel steel with approximately 2% of Molybdenum added to the straight 18-8 alloy which increases its strength at elevated temperatures and results in somewhat improved corrosion resistance.

 

 Has the highest creep strength at elevated temperatures of any conventional stainless type.

 

 Not suitable for extended service within the carbide precipitation range of 800º F to 1650º F. when corrosive conditions are severe.

 

 Recommended maximum working temperature of 1400º F.

316L Stainless Steel

 Continuous maximum temperature range of 1400º F -1500º F.

 

 Carbon content held at a maximum of .03%.

 

 Subject to a lesser degree of stress corrosion cracking and also to intergranular corrosion than Type 316.

321 Stainless Steel

 An 18-10 Chromium-Nickel steel with a Titanium addition.

 

 Type 321 stainless has the same characteristics as Type 347.

 

.

Additional Information:

• Production Capacity: 10000
• Delivery Time: 1 day
• Packaging Details: Box packing available

We are one of the leading manufacturers of a wide range of PTFE Ring Gasket. Our range of PTFE ring and gasket is manufactured using molding method with PTEF method with PTFE granular resin. PTFE, compared with other plastics, has superior properties against chemicals and temperature. The PTFE ring & gasket offered by us is highly admired by all our clients due to their high reliability as well as durability. These ring joint gaskets are especially designed to withstand exceptionally high assembly loads over a small area, thus producing high seating stresses.

Additional Information:

• Production Capacity: As Required
• Delivery Time: Ready